TEN CENTSMANUALASSEMBLY OPERATION MAINTENANCE PARTS LISTModel Nos. 137-460A137-465A137-460-300137-465-300Important:Read Safety Rules and Instructions
Step 6. Once the machine is in motion, remove foot from the pedal. The mower will now move ahead or to the rear, and the use of
Variable Speed—See page 28.Front Pivot Bar—Lubricate at least once a season with light oil.Steering and Drag Link—Should be lubricated onc
NOTEBelt tension is automatically maintained by the spring on the variable speed bracket on the drive belts and the belt tension o
Dimension “B” should be approximately 1 /8” less than Dimension “A”.A. ) To increase Dimension “B”, screw tie rod intotie rod end.B. ) To dec
FIGURE 27. REMOVING MOWER BELTStep 4. Place the lift lever in the engaged position. See figure 9.Step 5. Unhook the tension springs on both sides of t
step 8. Remove the engine belt guard by removing the two front engine mounting bolts. See figure 33.Step 9. Place the clutch lockout
Try and push the rider. If the rider can be moved tighten the brake adjustment nut as shown in figure 36.Step 3.NOTEThe adjusting nut
TROUBLE SHOOTING CHART FOR RECOIL START MODELSACAUTION: ALWAYS DISCONNECT SPARK PLUG BEFORE ATTEMPTING ANY REMEDY.TROUBLELOOK FORREMEDYEngine fails to
TROUBLE SHOOTING CHART FOR ELECTRIC START MODELSTROUBLEEngine fails to start.LOOK FORSafety SystemREMEDYBlocked fuel line or empty gas tank.Defecti
PARTS LIST FOR SCHEMATIC MODEL 137-460AREF.NO.PARTNO.DESCRIPTIONNEWPART1725-0269 Safety Switch Norm Closed- Red2725-0464Magneto Ignition Switch w/NutN
IMPORTANTIt is suggested that this manual be read in its entirety before attempting to assemble or operate. Keep this manual in a safe place for futur
137-465PARTS LIST FOR SCHEMATIC MODEL 137-460AREF.NO.PARTNO.DESCRIPTIONNEWPART1725-0268 Safety Switch—Black Plunger2 725-0364Wire Harness3 725-0202Lig
137-460A137-465ASHORT SHAFTLubricate with 2 oz. high temp, grease 450°F. Order part number 737-0120.PARTS LIST FOR DIFFERENTIAL ASSEMBLY 717-
717-0222 REVERSING TRANSMISSION11137-460A137-465APARTS LIST FOR REVERSING TRANSMISSION 717-0222REF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.
DECK LINKAGENOTERefer to illustration below for proper deck link hookup. If the deck is removed for any reason use the illustration be
137-460A137-465A33 3224
PARTS LIST FOR MODELS 137-460A AND 137-465A1.REF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART111263Plastic Handle (4
< <о ю со соI Iсо со(Оем
PARTS LIST FOR MODELS 137-460A AND 137-465AREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1731 -0220Steering Wheel
137-460A137-465APart of EngineNOTE: If for any reason disc brake is disassembled, be sure round end of push pin (Ref. No. 51) is to
PARTS LIST FOR MODELS 137-460A AND 137-465AREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1_Engine49 HH-02-03631 Lo
INDEXSafe Operation Practices...2Index and Assembly...3Ba
137-137-460A465A3i‘*IMPORTANTBeits listed by Part Number are of special construction and should be used when replacement is necessary. T
PARTS LIST FOR MODELS 137-460A AND 137-465AREF.Jj40.PARTNO.COLORCODEDESCRIPTION1711-0494Spacer .510 I.D. x .760 O.D. X .390210438Variable Spd. Pulley
PARTS INFORMATIONPOWER EQUIPMENT PARTS AND SERVICEPorts and service for oil MTD manufactured power equipment are available through the aut
step 3. Secure with Belleville washer and hex nut. See figure 2.Step 4. Press the cap on the steering wheel by hand. See figure 2.BATTERY INFORMATIONS
5.B.The battery can now be charged after the 20 minutes setting period. Battery can be SLOW CHARGED (DO NOT FAST CHARGE) at a maxi
3. Cut the black rubber tubing approximately 4 inches long.4. Push the rubber tubing into the manifold of the battery and place the
c. Brake. The brake pedal is located on the right hand side of the mower and is operated by depressing it with your right foot. See f
^ R'ocoil Starter I (Shown Locked)FIGURE 11. RECOIL STARTERk. Recoil Starter. The recoil starter is located on the right side of th
OPERATINGINSTRUCTIONSSTARTING THE ENGINEBe sure to follow the instructions for the oil and gasoline as described in the engine manual.Step 1.
Comments to this Manuals