.50ASSEMBLY OPERATION MAINTENANCE PARTS LISTIMPORTANT: Read Safety Rules and InstructionsMODEL NUMBER 130-360A25"RIDINGMOWERPRINTED IN U.S.A.FORM
MAINTENANCECRANKCASE OILI WARNING {Remove the spark plug lead before performing any maintenance on the machine.a. Oil CheckCheck the oil l
FIGURE 18. LUBRICATIONFIGURE 19. LUBRICATIONBRAKE ADJUSTMENTThe brake adjustment is made by tightening the hex nut on the brake band to
step 2. Remove the blade by removing the hex head cap screw in the center of the blade. Hold the blade with one hand and using a V 2" o
NOTEWrap a rag around the blade to protect your hand.Step 3. Take off the deck by removing the six hex nuts and lock washers as shown in figure 23.St
BLADE PULLEYSRaise front of mower approximately a foot off the ground and support it with blocks. Sight down blade belt from front of
TROUBLE SHOOTING CHART FOR RECOIL START MODELSCAUTION; ALWAYS DISCONNECT SPARK PLUG BEFORE ATTEMPTING ANY REMEDY.TROUBLELOOK FORREMEDYEngine will not
130-360ASINGLE SPEED TRANSMISSION PART NO. 717-0223REF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1 716-0104Snap Ri
130-360ARECOIL WIRINGPARTS LIST FOR WIRINGREF.NO.PARTNO.DESCRIPTIONNEWPART1 725-0269 Safety Switch—Red(2 Req’d.)2725-0464Magneto Ignition Switchw/Nut7
130-360AIF YOU WRITE TO US ABOUT THIS ARTICLE OR IF YOU ORDER REPLACEMENT PARTS ALWAYS MENTION THIS MODEL & SERIAL NO MODEL!!0 109NOTEThis instr
PARTS LIST FOR MODEL 130-360AREFNO: PART NO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTION"NEWPART1757-0265Seat5907386 FI-Wash. .3
INDEXSafe Operation Practices...3Assembly Instructions...4Controls...
coco оcoоCM
PARTS LIST FOR MODEL 130-360AREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1712-0267 Hex Nut 5/16-18 Thd.‘2736-0119Spring L-Washer 5/16" Scr.*3 713-03
130-360AEngineTransmission ]Q22
PARTS LIST FOR MODEL 130-360A^REF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART109296Exhaust Deflector31 712-0123Hex
130-360A24
PARTS LIST FOR MODEL 130-360AREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1 731-0220Steering Wheel Cap2 712-0158Hex Center Lock Nut 5/16-183736-0242Thd.*B
PARTS INFORMATIONPOWER EQUIPMENT PARTS AND SERVICEParts and service for all MTD manufactured pov^er equipment are available through the au
IMPORTANTIt is suggested that this manual be read in its entirety before attempting to assemble or operate. Keep this manual in a safe place for futur
BASSEMBLYi :TOOLS REQUIRED FOR ASSEMBLY -See figure 1.A (1) V 2" Box or Open End Wrench B (1) V4 " Flat Screwdriver C (2) 7/16" Box or
1. Place steering shaft (F) pinion in steering gear and fasten with two hex sems bolts (L). A V2" wrench is required. See figure 4.FIGURE 4. 2.
'1 V. ^ >4* iTiuss Scrpw Truss Screw (B) (A)‘ I \ «; lb-4. Assemble the hood with 5/8" truss screws (A) to the rear of hood, and
7. Position the trailer hitch on the center of the rear frame section and fasten with bolts A and— nuts B. See figure 10.8. Check ALL nuts and bolts
Engage the Lever slowly.NOTEBladeEngagementFIGURE 13.E. The Gear Shift Lever is used to select either forward or reverse. See figure 11.NOTE
NOTEIf the Recoil Starter Handle is not locked after engine starts, putting the rider into motion will stop the engine.PUTTING THE RID
Comments to this Manuals