.50ASSEMBLY » OPERATION » MAINTENANCE « PARTS30" RIDING MOWERImportant:Read Safety Rules and Instructions CarefullyThank you for purchasing an Am
13. Feed the end of the battery drain tube into the------hole provided in the frame, located in front ofthe starter on the engine. See figure 16.FIGU
TIRE PRESSUREFOR SHIPPING PURPOSES, THE TIRES ON YOUR UNIT MAY BE OVER-INFLATED. TIRE PRESSURE SHOULD BE REDUCED BEFORE UNIT IS PUT INTO OPERATION.
'i Iï:'Blade Engageme Lever (DisengagedFIGURE 20.To engage the blade, move the blade toward the front of the unit as shown in
BRAKETo operate the brake, depress the right pedal all the way. To lock the brake in park position, depress the right pedal all t
STOPPINGI WARNING JDo not operate the rider if the inter- iock system is malfunctioning because it is a safety device, designed for protection.5.
To Adjust: (See figure 25)Place remote control lever on equipment in “FAST” (high speed) position.Lever C on carburetor should be just to
CLUTCH ROD ADJUSTMENT1. With the engine off, reiease the clutch lock.2. There should be 1/2" of space between the end of slot and clutch
MAINTENANCE\ WARNING {Disconnect spark plug wire and ground it against the engine before performing any repairs or maintenance.CUTTING B
AIR CLEANERService air cieaner every 25 hours under normal conditions. Clean every few hours under extremely dusty conditions. Poor engine per
4. Tip the rider up on its back wheeis. See figure 31. Tipping unit up against a wail is recommended.5. Block unit to prevent tipping.Remov
INDEXSafe Operation Practices...3Assembly Instructions...4Battery Informati
FIGURE 36.6. Remove the hex lock nut from the idler pulley, located on the left hand side of the deck. A 9/16" wrench is required. See
9. Set the deck aside.Removing the Cutting Deck Belt:Follow preceding instructions on “Preparation” and “Removing the Cutting Deck.”Remove engin
5. Reverse the preceding steps to reassemble. NOTE 'Be certain all belts are inside belt guards and keepers. Also, be sure to reassemble
TROUBLE SHOOTING CHART FOR ELECTRIC START MODELSTROUBLELOOK FORREMEDYEngine will not crankBattery installed incorrectlyThe battery must be instal
TROUBLE SHOOTING CHART FOR ELECTRIC START MODELSTROUBLELOOK FORREMEDYNo spark to spark plugSpark plug lead disconnected. Connect lead. Hold spark
131-410APARTS LIST FOR ELECTRICAL SYSTEM MODEL 131-410AREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1725-0150 Electric Wire (Starter)2725-0530 Solenoid3 7
131-410AIF YOU WRITE TO US ABOUT THIS ARTICLE OR IF YOU ORDER REPLACEMENT PARTS ALWAYS MENTION THIS MODEL & SERIAL NO MODELMAIN BODY26
131-41 OAPARTS LIST FOR MAIN BODY MODEL 131-410AREF.NO.PART 1 COLOR NO. 1 CODEDESCRIPTIONNEWPART1757-0265Seat Complete2710-0289Hex Bolt 1/4-20 X .50&q
131-410A50FRAME VIEW28
1 O 1 "H 1 UM PARTS LIST FOR FRAMEVIEW MOD EL 131-410AREF. PARTCOLORNEW REF. PARTCOLORNEWNO.NO.CODEDESCRIPTIONPARTNO.NO. CODEDESCRIPTIONPART1 731
^ WARNING \To reduce the potential for any injury, compiy with the following safety instructions. Failure to comply with the instructions may result i
NOTE: If mower fails to respond to speed control lever, it is possibie that the variabie speed puiley is seizing. Apply a few drops of131-410A
131-410APARTS LIST FOR DECK AND BELT SYSTEMMODEL 131-410AzF.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1_Engine30710-0
131-410AFor parts on top of this page, refer to page 30.IMPORTANTBelts listed by Part Number are of special construction and should be us
131-410APARTS LIST FOR DECK AND BELT SYSTEMMODEL 131-410A,0.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1754-0251Deck “
PARTS LIST FOR DIFFERENTIAL ASSEMBLY 717-0328REF.NO.PARTNO.Qty.Req’d.DESCRIPTIONNEWPART1 715-02472Spring Pin Spin 3/16" Dia. x 1.00" Lg.2 74
131-410A717-0223 REVERSING TRANSMISSION//Unit requires approximately five (5) ounces of high temperature iubri- cant.PARTS LiST FOR REVERSING TFAN
PARTS INFORMATIONPOWER EQUIPMENT PARTS AND SERVICEParts and service for all MTD manufactured power equipment are available through the authorized
A-—a ri ii ?ASSEMBLY INSTRUCTIONSNOTEThis unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fue
Rear CoverSeatHex Bolt (E) Lock Washer (F) Flat Washer (G)2.Place the seat over cover and fasten with four hex bolts (E), lock washers (F) an
Cover(K)^ r5. Place the cover over the steering tube assembly. Line up holes in cover with speed— nuts. See figure 6.6. Secure cover (K) to
BATTERY INFORMATIONA.B.C.I WARNING ^Battery acid must be handled with great care as it wili biister the skin and damage clothing. It is
ScrewdriverFill Caps4. Remove the six fill caps from the top of the — battery. A screwdriver will make it easier. See figure 10.FIGURE 10..! ; , ;Larg
9.Place the battery in the rider, so that the positive terminal is towards the right side of •the unit. See figure 13.NOTERight and l
Comments to this Manuals